FL type 30W series 2-channel output

• Compact size and lightweight.

• High reliability and low price.

• Wide input voltage range.

• High conversion efficiency and low operating temperature rise.

• Built-in filter circuit, minimizing external radiated interference.

• Basic protection circuitry, providing good environmental adaptability.

• 4-hour, 100% full load aging and full range of functional tests.

Features
Model
Parameters

SFLD-030-2L

SFLD-030-2A

SFLD-030-2G

SFLD-030-2R01

SFLD-030-2K

Rated Output Voltage

DC +12V  -12V

DC +12V  5V 

DC +5V  12V 

DC+15   -15V 

DC +24V   5V 

Output Interface Location

The black P=8.5 six-pin connector is labeled DC1, COM, DC2, etc.

Output Voltage Range

Setting error: ±0.5V; Adjustable range: ±10%

Setting error: ±0.5V;

Rated Output Current

2A    1A

2.5A   1.5A

3A    1.5A

1.5A   1A

1A     1A

Output Voltage Ripple

Vp-p100Hz<50mV；Vp-pmax<150 mV

Vp-p100Hz<50mV；Vp-pmax<200 mV

Li;Lo Regulation

Line:±0.5%；Load:±0.5%

Line:±1%；Load:±5%

Overall Voltage Regulation Accuracy

±3%

±10%

Rated Output Power

30W

Rated Operating Efficiency

≈80% (output power is rated, AC220V)

Rated Input Voltage

Input range: AC100~240V; Rated voltage: AC220V. Interface position: Three-position covered socket labeled AC-L, AC-N, FG (with wire).

Rated Input Current

Rated current: AC 0.4A (AC 220V), current range AC 0.3～0.5A

AC Input Frequency

Rated AC voltage frequency range 47～63Hz, sine wave

Inrush Current

The inrush current to the power grid at the moment of power-on: the maximum value during cold start is 20A/10ms.

Input Overvoltage Protection

Input allowable range: AC0～280V; Overvoltage protection point: AC300V±5V, power supply enters irreversible shutdown state.

Output Overload Protection

The overload protection point is approximately 110%~150% of the rated output power; the overload protection is an online power limiting and voltage reduction method.

Power supply timing parameters

Setup time ≈ 200ms; Settlement time ≈ 50ms; Hold-up time ≈ 20ms

Dielectric strength parameters

[Input-Output: AC1.5KV; Input-Casing: AC1.5KV] Leakage current <5mA 50Hz 1min.

Operating temperature parameters

The operating temperature drift coefficient is approximately ±0.03 [%/℃]; the absolute temperature rise coefficient is approximately 0.50 [℃/W]; the absolute temperature rise of the chassis when operating at rated power is 30℃±5℃.

Environmental conditions parameters

Storage environment: -20℃ to +85℃; 10% to 95%RH. Operating environment: -10℃ to +50℃; 20% to 90%RH. (Varies depending on the operating environment and power consumption)

Cooling method

Designed for continuous operation, with self-cooling and heat dissipation assistance. (Power consumption and lifespan are affected by differences in the usage environment and installation location.)

External dimensions and mounting dimensions

Specifications: L88×W70×H38mm³; Maximum size: L88×W85×H38mm³; Installation dimensions: Bottom L78×W74mm², Side L78×W0mm²

Net weight and color

Total weight 200g; bottom shell is 1.5mm thick aluminum with a white sandblasted finish; top shell is 0.7mm thick iron with a white finish.

Certification Security Specifications

National Standards GB-4943 and GB-9254

Note: 1) All the above test indicators were measured under the following conditions: within the rated input voltage and rated output load range, the environment was 25℃, 85%RH, and there was no wind.

2) Output DC voltage ripple test: A parallel stranded wire with a length of 30cm and a cross-section of 1mm², with 0.1μF and 0.47μF capacitors connected to one end, was bypassed at the test point. The maximum peak-to-peak value of the main frequency ripple Vp-p100Hz and the maximum peak-to-peak value of the combined ripple Vp-pmax were measured respectively.

3) Li voltage regulation rate: When the load is at the rated value, the input voltage varies within the rated range; Lo load regulation rate: When the input is at the rated voltage value, the load varies from zero to the rated value.