SBBA-030-2G

• Compact size and lightweight.

• High reliability and low price.

• Wide input voltage range.

• High conversion efficiency and low operating temperature rise.

• Built-in filter circuit, minimizing external radiated interference.

• Basic protection circuitry, providing good environmental adaptability.

• 4-hour, 100% full load aging and full-series functional testing.

Features
Model
Parameters

SBBA-030-2G

Rated Output Voltage

DC1  +5V

DC2　12V

Output Interface Location

The black 8.5mm P six-position connector is labeled DC2, COM, and DC1 respectively.

Output Voltage Range

Setting error < ±5%

Setting error < ±10%

Rated Output Current

Rated current 3A; Current range 0.1A --- 3A

Rated current 1.5A; Current range 0-1.5A

Output Voltage Ripple

Vnor＜20mv  Vp_p100Hz＜50mv  VP-Pmax＜100mv

Vnor＜50mv  Vp_p100Hz＜100mv  VP-Pmax＜120mv

Li;Lo Regulation

Line: ±0.5%    Load: ±4%

Line: ±0.5%    Load: ±8%

Overall Voltage Regulation Accuracy

±5%

±10%

Rated Output Power

30W

Rated Operating Efficiency

≈80% (output power is rated, AC220V)

Rated Input Voltage

Input range: AC220±15%V; Rated voltage: AC220V. Interface position: Three-position covered socket marked FG, AC-L, AC-N.

Rated Input Current

Rated current: AC 0.4A (AC 220V), current range AC 0.3～0.5A

AC Input Frequency

Rated AC voltage frequency range 47～63Hz, sine wave

Inrush Current

The inrush current to the power grid at the moment of power-on: the maximum value during cold start is 20A/10ms.

Input Overvoltage Protection

Input allowable range: AC0～280V; Overvoltage protection point: AC300V±5V, power supply enters irreversible shutdown state.

Output Overload Protection

The overload protection point is approximately 110%~180% of the rated output power; the overload protection is an online power limiting and voltage reduction method.

Power supply timing parameters

Setup time ≈ 200ms; Settlement time ≈ 50ms; Hold-up time ≈ 20ms

Dielectric strength parameters

[Input-Output: AC1.5KV; Input-FG: AC1.5KV] Leakage current <5mA 50Hz 1min.

Operating temperature parameters

The operating temperature drift coefficient is approximately ±0.03 [%/℃]; the absolute temperature rise coefficient is approximately 0.50 [℃/W]; the absolute temperature rise of the chassis when operating at rated power is 30℃±5℃.

Environmental conditions parameters

Storage environment: -20℃ to +85℃; 10% to 95%RH. Operating environment: -10℃ to +50℃; 20% to 90%RH. (Varies depending on the operating environment and power consumption)

Cooling method

Designed for continuous operation, with self-cooling and heat dissipation assistance. (Power consumption and lifespan are affected by differences in the usage environment and installation location.)

External dimensions and mounting dimensions

See attached installation dimension diagram

Net weight and color

Total weight 100g;

Certification Security Specifications

National Standards GB-4943 and GB-9254

Note: 1) All the above test indicators were measured under the following conditions: within the rated input voltage and rated output load range, the environment was 25℃, 85%RH, and there was no wind.

2) Output DC voltage ripple test: A parallel stranded wire with a length of 30cm and a cross-section of 1mm², with 0.1μF and 0.47μF capacitors connected to one end, was bypassed at the test point. The maximum peak-to-peak value of the main frequency ripple Vp-p100Hz and the maximum peak-to-peak value of the combined ripple Vp-pmax were measured respectively.

3) Li voltage regulation rate: When the load is at the rated value, the input voltage varies within the rated range; Lo load regulation rate: When the input is at the rated voltage value, the load varies from zero to the rated value.