KJ series 150W

• Compact size and lightweight.

• High reliability and low price.

• Wide input voltage range.

• High conversion efficiency and low operating temperature rise.

• Built-in filter circuit, minimizing external radiated interference.

• Basic protection circuitry, providing good environmental adaptability.

• 8-hour, 100% full load aging and full-range functional testing.

Features
Model
Parameters

SKJA-150-1F

SKJA-150-1B

SKJA-150-1H

Rated Output Voltage

6.5V

24V

12V

Output Interface Location

The seven 9.5-M4 connectors are labeled OUTPUT: DC+, DC-.

Output Voltage Range

Setting error: ±3%; Adjustable range: ±15%

Rated Output Current

Rated value 25A, operating current range 0～25A

Rated value 6.5A, operating current range 0～6.5A

Rated value 13A, operating current range 0～13A

Output Voltage Ripple

Vnor<20mV；Vp-p100Hz<50mV；Vp-pmax<80mV

Li;Lo Regulation

Line:±0.5%；Load:±0.5%

Overall Voltage Regulation Accuracy

±3%

Rated Output Power

150W

Rated Operating Efficiency

≥75% (output power is rated)

Rated Input Voltage

Rated voltage: AC220±15%, Operating voltage: AC220±20%. Interface: Seven-pin 9.5-M4 interface, labeled INPUT: AC-L, AC-N, FG.

Rated Input Current

Rated current: AC220V: AC0.85A, current range AC0.7A～1.2A;

AC Input Frequency

Rated AC voltage frequency range 47～63Hz, sine wave

Inrush Current

The surge current to the power grid at the moment of power-on: the maximum value during cold start is 20A/10ms.

Input Overvoltage Protection

Input allowable range: AC0～280V; Overvoltage protection point: AC300V±5V, power supply enters irreversible shutdown state.

Output Overload Protection

The overload protection point is approximately 110% of the rated output current, and the protection is a current-limiting and voltage-reducing method; the short-circuit protection is an online voltage-drop shutdown method, and the input needs to be reset to restore it.

Overheat protection

The overheat protection point is 85℃±5℃, and the protection method is online shutdown. Normal operation resumes when the overall machine temperature drops below 50℃±3℃.

Multi-unit series/parallel operation

Multiple power supplies of the same series are allowed to be used in series and parallel (parallel operation with uneven current distribution).

Power supply timing parameters

Setup time ≈ 200ms; Settlement time ≈ 50ms; Hold-up time ≈ 20ms

Isolation voltage parameters

[Input-Output: AC1.5KV, Input-Casing: AC1.5KV, Output-Casing: AC0.5KV] 50Hz, Power-on for 1 minute: Leakage current <8mA

Operating temperature parameters

The operating temperature drift coefficient is approximately ±0.05 [%/℃]; the absolute temperature rise coefficient is approximately 0.2 [℃/W]; when the operating output is at rated power, the absolute temperature rise of the machine body is 25℃±5℃.

Environmental conditions parameters

Storage environment: -20℃ to +85℃; 10% to 95%RH. Operating environment: 0℃ to +50℃; 20% to 90%RH. (Varies depending on the operating environment and power consumption)

Cooling method

Designed for continuous operation with natural cooling (power consumption is affected by the operating environment and installation location).

External dimensions and mounting dimensions

Specifications: L159×W98×H47mm³; Maximum size: L160×W100×H48mm³; Installation dimensions: L150×W85mm², L149×W10mm²

Net weight and color

The total weight is approximately 500g; the bottom shell is made of 1.5mm thick aluminum with a polished and anodized finish; the top shell is made of 0.6mm thick iron with a nickel-plated finish.

Design standards

National Standards GB-4943 and GB-9254

Note: 1) All the above test indicators were measured under the following conditions: within the rated input voltage and rated output load range, the environment was 25℃, 85%RH, and there was no wind.

2) Output DC voltage ripple test: A parallel stranded wire with a length of 30cm and a cross-section of 1mm², with 0.1μF and 0.47μF capacitors connected to one end, was bypassed at the test point. The maximum peak-to-peak value of the main frequency ripple Vp-p100Hz and the maximum peak-to-peak value of the combined ripple Vp-pmax were measured respectively.

3) Li voltage regulation rate: When the load is at the rated value, the input voltage varies within the rated range; Lo load regulation rate: When the input is at the rated voltage value, the load varies from zero to the rated value.